Replace thrust bearing and thrust washer if rusted or damaged. Apply constant pressure to cam follower in order to prevent it and internal components from ejecting out of the propeller shaft during removal of the cross pin from the clutch. . This allows not only to reduce harmful emissions into the atmosphere, but also to increase the efficiency of the motors themselves, as well as to reduce the specific fuel consumption. This is a must for the Do-It-Yourselfer! This is a must for the Do-It-Yourselfer! If the bearing needs to be replaced remove it using Slide Hammer 91-34569A1. It compensates for the initial wear that occurs during the life of the outboard motor.
Replace pinion gear if it is chipped or worn. Remove drive shaft, pinion gear, pinion bearing and forward gear. V6 3130cc 2-stroke 1994, 225 hp 90 deg. Remove bearing from gear using Universal Puller Plate 91-37241 and mandrel. This is a must for the Do-It-Yourselfer! This is a must for the Do-It-Yourselfer! Prop shaft trueness should be measured with a dial indicator with prop shaft on V-blocks. Remove water pump base using flat screwdrivers to lightly pry up on base. Use suitable tools screwdriver and awl to remove retaining ring.
So please make sure your email address is correct. Replace upper drive shaft bearing and sleeve if either are rust stained, or if bearing will not roll freely. This is a must for the Do-It-Yourselfer! This is a must for the Do-It-Yourselfer! Remove propeller shaft seals if not removed with bearing in Step 9 and bearing carrier O-ring. The information on this manual covered everything you need to know when you want to repair or service Yamaha 25S Outboard. Replace cover if thickness of steel at the discharge slots is 0. Lift impeller, drive key, and gasket from drive shaft. Replace reverse gear if gear teeth or clutch teeth on reverse gear are rounded or chipped.
From basic maintenance and troubleshooting to complete overhauls, our Yamaha Four-Stroke Outboard manuals provide the information you need. Remove bearing and then sleeve using Puller Assembly 91-83165M with suitable jaws. Exact Models Covered Covers All 1996-1997 Models World Wide : F8B F8-B , F9. Clymer Yamaha Four-Stroke Outboard manuals are written specifically for the do-it-yourself enthusiast. If today we ask the owners of boats and in various parts of the world, whatever motor they wanted to buy for their boat, then the Yamaha engines will be the first in the rating, so firmly established in their minds is the image of Yamaha Motor Co. Take care not to lose cam follower or 3 metal balls in end of propeller shaft.
If reverse gear radial bearing is rusted or does not roll freely, replace bearing. Replace forward gear needle bearing if it is rusted or does not roll freely. This is a must for the Do-It-Yourselfer! Replace cam follower if worn or pitted. Your will receive a download link immediately after your payment is completed. With propeller shaft horizontal, pull carrier using tool shown to break seal with gear housing.
Remove components from propeller shaft. Models Covers: Model name model code Starting serial No. Replace forward gear bearing and race if either are rusted, pitted or damaged, or if bearing does not roll freely. How to adjust the oil linkage on a 2007 200 hp yamaha how to change a impeller on mariner 200 hp how to change jet pump prop lower unit on yah ama 200 hp how to diagnose fuel system problems on a 1994 mercury 200 hp efi how to disconnect 200 hp outboard johnson shift cable 1996 how to fix a jhonson 1996 200 hp how to repair trim and tilt sending unit on 200 hp yamaha outboard how to replace an evinrude 200 hp temperature switch how to set carburetor on 200 hp Yamaha how to set idle speed on 98 200 hp mercury outboard how to trouble shoot 200 hp yahama ecu module how to clean Yamaha oil injection 200 hp 2998 how to wire key switch on 200 hp johnson i have a 1993 200 hp 2 stroke johnson outboard motor. This is a must for the Do-It-Yourselfer! Keep this manual handy and use it often. The Yamaha outboard motor service manual downloads for the above listed models describes the service procedures for the complete engine. The subsequent pages give detailed procedures.
Replace water tube seal, if damaged. Your will receive a download link immediately after your payment is completed. So please make sure your email address is correct. If bearing is rusted or does not roll freely, replace bearing. Motor tilt not holding in reverse yamaha 200 hp no voltage at gauge yamaha 200 hp outboar shift cable adjustment yamaha 200 hp outboard manual yamaha 200 hp outboard service manual yamaha 200 hp pro v outboard compression yamaha 2014 200 hp outboard manual yamaha manual for 200 hp yamaha manual for 200 hp 2 stroke 2006 yamaha outboard 200 hp power trim is leaking yamaha outboard motor 200 hp 1986 year on low of torque yammaha 200 hp serial number location 2000 johnson outboard ss 130 200 225 250 hp 90 degree v models service manual manual for 200 johnson 60 hp 2 stroke outboard what is the difference between a 1988 suzuki 150 hp outboard and 200.